

| Parameter | Value |
|---|---|
| GTIN | 4055626793764 |
| Orderkey | 1078681 |
| (General) | 20 ... 12 (flexible) |
| (Drawings) | The system installer must ensure the touch protection of the product (at voltages > 25 V AC/60 V DC). The product is a built-in device without protection against direct contact. |
| (Coil side) | 6 A (at 250 V, AC15) |
| Catalog page | Page 336 (C-5-2019) |
| Depth (Note) | 75 mm |
| Packing unit | 1 pc |
| Width (Note) | 16 mm |
| (Dimensions) | ≥ IP54 (Installation location) |
| Height (Note) | 89 mm |
| Note (Drawings) | FBS 2-6... plug-in bridge for the input side (A2) and FBS-2-8... plug-in bridge for the output side (11/21) |
| Torque (General) | 0.5 Nm ... 0.6 Nm |
| Country of origin | CN (China) |
| ETIM 5.0 (eCl@ss) | EC001437 |
| ETIM 6.0 (eCl@ss) | EC001437 |
| ETIM 7.0 (eCl@ss) | EC001437 |
| (Connection data) | 20 ... 12 (flexible) |
| (Connection data 2) | EN 61810-1 |
| Custom tariff number | 85364190 |
| (Ambient conditions) | Free-wheeling diode Damping diode |
| Type of note (Drawings) | Notes on operation |
| Contact type (Coil side) | 1 N/O contact |
| Torque (Connection data) | 0.5 Nm ... 0.6 Nm |
| Connection name (General) | Coil side |
| Stripping length (General) | 8 mm |
| Connection method (General) | Screw connection |
| (Standards and Regulations) | For details about hazardous substances go to tab “Downloads”, Category “Manufacturer's declaration” |
| Contact material (Coil side) | AgSnO |
| eCl@ss 5.0 (Classifications) | 27371600 |
| eCl@ss 5.1 (Classifications) | 27371600 |
| eCl@ss 6.0 (Classifications) | 27371600 |
| eCl@ss 7.0 (Classifications) | 27371601 |
| eCl@ss 8.0 (Classifications) | 27371601 |
| eCl@ss 9.0 (Classifications) | 27371601 |
| Maximum altitude (Dimensions) | ≤ 2000 m |
| Operating mode (Contact side) | 100% operating factor |
| Insulation (Connection data 2) | Safe isolation, reinforced insulation |
| Switching capacity (Coil side) | 2 A (at 24 V, DC13) |
| Designation (Connection data 2) | Standards/regulations |
| Mounting position (Contact side) | any |
| Coil voltage (Ambient conditions) | 24 V DC |
| Connection name (Connection data) | Contact side |
| Degree of protection (Dimensions) | RT II (Relay) |
| Maximum inrush current (Coil side) | 165 A (20 ms) |
| Min. switching current (Coil side) | 100 mA (at 12 V DC) |
| Stripping length (Connection data) | 8 mm |
| Type of switch contact (Coil side) | Single contact |
| Utilization restriction (Drawings) | EMC: class A product, see manufacturer's declaration in the download area |
| Connection method (Connection data) | Screw connection |
| Switching capacity min. (Coil side) | 1200 mW |
| Assembly instructions (Contact side) | In rows with zero spacing |
| Pollution degree (Connection data 2) | 2 |
| Weight per Piece (excluding packing) | 0.000 g |
| Conductor cross section AWG (General) | 20 ... 10 (solid) |
| Maximum switching voltage (Coil side) | 250 V AC/DC |
| Minimum switching voltage (Coil side) | 12 V (at 100 mA) |
| China RoHS (Standards and Regulations) | Environmentally Friendly Use Period = 50 |
| Mechanical service life (Contact side) | 3x 107cycles |
| Conductor cross section solid (General) | 0.5 mm² ... 4 mm² |
| Limiting continuous current (Coil side) | 6 A |
| Protective circuit (Ambient conditions) | Reverse polarity protection Polarity protection diode |
| Rated surge voltage (Connection data 2) | 6 kV |
| Overvoltage category (Connection data 2) | III |
| Standards/regulations (Connection data 2) | EN 50178 |
| Typical release time (Ambient conditions) | 10 ms |
| Conductor cross section flexible (General) | 0.5 mm² ... 4 mm² |
| Typical response time (Ambient conditions) | 8 ms |
| Ambient temperature (operation) (Dimensions) | -40 °C ... 70 °C |
| Conductor cross section AWG (Connection data) | 20 ... 10 (solid) |
| Nominal input voltage UN (Ambient conditions) | 24 V DC |
| Note regarding the switch contact (Coil side) | With tungsten leading contact |
| Operating voltage display (Ambient conditions) | Yellow LED |
| Conductor cross section solid (Connection data) | 0.5 mm² ... 4 mm² |
| Typical input current at UN (Ambient conditions) | 18 mA |
| Interrupting rating (ohmic load) max. (Coil side) | 264 W (at 24 V DC, observe contact derating) |
| Conductor cross section flexible (Connection data) | 0.5 mm² ... 4 mm² |
| Ambient temperature (storage/transport) (Dimensions) | -40 °C ... 85 °C |
| Test voltage relay winding/relay contact (Contact side) | 4 kV AC (50 Hz, 1 min.) |
| Input voltage range in reference to UN (Ambient conditions) | see diagram |
| Power dissipation for nominal condition (Ambient conditions) | 0.43 W |
| Conductor cross-section solid (2 conductors with same cross section) (General) | 0.5 mm² ... 2.5 mm² |
| Conductor cross section flexible (2 conductors with same cross section) (General) | 0.5 mm² ... 2.5 mm² |
| Conductor cross-section solid (2 conductors with same cross section) (Connection data) | 0.5 mm² ... 2.5 mm² |
| Conductor cross section flexible (2 conductors with same cross section) (Connection data) | 0.5 mm² ... 2.5 mm² |
| DiagramCurve AMaximum permissible continuous voltage Umaxwith limiting continuous current on the contact side (see relevant technical data)Curve BMinimum permissible operate voltage Uopafter pre-excitation (see relevant technical data) (Drawings) |
Technical specifications and performance data
Installation and operation guide