In Stock Hot Product
PLC-RPT-24DC/ 1IC/ACT
PLC-RPT- 24DC/ 1IC/ACT 2900298 PHOENIX CONTACT Relay Module
$0.00USD
3985 in stock
Key Specifications
():IP20 (Relay base)
GTIN:4046356507370
Note ():Separating plate PLC-ATP must be installed for voltages larger than 250 V (L1, L2, L3) between identical terminal blocks in adjacent modules.
Orderkey:2900298
Supplier Information
Products: 0
Usually ships within 2-3 business days
Quality Guaranteed
Fast Shipping
Technical Support
Technical Specifications
| Parameter | Value |
|---|---|
| () | IP20 (Relay base) |
| GTIN | 4046356507370 |
| Note () | Separating plate PLC-ATP must be installed for voltages larger than 250 V (L1, L2, L3) between identical terminal blocks in adjacent modules. |
| Orderkey | 2900298 |
| (General) | EN 61810-1 |
| (Coil side) | 6 A (at 250 V, AC15) |
| Catalog page | Page 386 (C-5-2017) |
| Depth (Note) | 94 mm |
| Packing unit | 10 pc |
| Width (Note) | 14 mm |
| Height (Note) | 80 mm |
| (Contact side) | 2x 0.5 mm² ... 1 mm² () |
| Coil voltage () | 24 V DC |
| Country of origin | DE (Germany) |
| Operating mode () | 100% operating factor |
| Net weight (SAP) () | 56.8 g |
| Custom tariff number | 85364190 |
| Insulation (General) | Safe isolation, reinforced insulation |
| Mounting position () | any |
| Designation (General) | Standards/regulations |
| Protective circuit () | Reverse polarity protection Polarity protection diode |
| (Key Commercial Data) | The system installer must ensure the touch protection of the product (at voltages > 25 V AC/60 V DC). The product is a built-in device without protection against direct contact. |
| Degree of protection () | RT II (Relay) |
| Maximum altitude (Note) | ≤ 2000 m |
| Typical release time () | 10 ms |
| Assembly instructions () | In rows with zero spacing |
| Contact type (Coil side) | 1 N/O contact |
| Typical response time () | 8 ms |
| Mechanical service life () | 3x 107cycles |
| Note (Key Commercial Data) | Separating plate PLC-ATP must be installed for voltages larger than 250 V (L1, L2, L3) between identical terminal blocks in adjacent modules. |
| Nominal input voltage UN () | 24 V DC |
| (Standards and Regulations) | For details about hazardous substances go to tab “Downloads”, Category “Manufacturer's declaration” |
| Contact material (Coil side) | AgSnO2 |
| Operating voltage display () | Yellow LED |
| Degree of pollution (General) | 2 |
| Rated surge voltage (General) | 6 kV |
| Connection name (Contact side) | Contact side |
| Overvoltage category (General) | III |
| Switching capacity (Coil side) | 2 A (at 24 V, DC13) |
| Typical input current at UN () | 18 mA |
| Standards/regulations (General) | EN 50178 |
| Stripping length (Contact side) | 8 mm |
| Connection method (Contact side) | Push-in connection |
| Maximum inrush current (Coil side) | 80 A (20 ms) |
| Min. switching current (Coil side) | 100 mA (at 12 V DC) |
| Rated insulation voltage (General) | 250 V AC |
| Type of switch contact (Coil side) | Single contact |
| Switching capacity min. (Coil side) | 1200 mW |
| Weight per Piece (excluding packing) | 56.800 g |
| Maximum switching voltage (Coil side) | 250 V AC/DC (The separating plate PLC-ATP should be installed for voltages larger than 250 V (L1, L2, L3) between identical terminal blocks in adjacent modules. Potential bridging is then carried out with FBST 8-PLC... or ...FBST 500...) |
| Minimum switching voltage (Coil side) | 12 V (at 100 mA) |
| Ambient temperature (operation) (Note) | -40 °C ... 60 °C |
| China RoHS (Standards and Regulations) | Environmentally Friendly Use Period = 50 |
| Limiting continuous current (Coil side) | 6 A |
| Conductor cross section AWG (Contact side) | 26 ... 14 |
| Connection in acc. with standard (General) | CUL |
| Power dissipation for nominal condition () | 0.43 W |
| Test voltage relay winding/relay contact () | 4 kV AC (50 Hz, 1 min.) |
| Conductor cross section solid (Contact side) | 0.14 mm² ... 2.5 mm² |
| Utilization restriction (Key Commercial Data) | EMC: class A product, see manufacturer's declaration in the download area |
| Ambient temperature (storage/transport) (Note) | -40 °C ... 85 °C |
| Conductor cross section flexible (Contact side) | 0.14 mm² ... 2.5 mm² |
| Flammability rating according to UL 94 (General) | V0 |
| Interrupting rating (ohmic load) max. (Coil side) | 144 W (at 24 V DC) |
| Interrupting rating (ohmic load) max. bridged (Coil side) | 240 W (for 24 V DC. The value is permissible if both connections 13, both connections 14 and both connections BB are bridged.) |
Product Description
PLC-INTERFACE for high clamping currents, consisting of PLC-BPT.../1 IC/ACT base terminal block with push-in connection and plug-in miniature relay, for mounting on NS 35/7.5 rail, max. clamping curre
Key Features
- Industrial grade quality
- RoHS compliant
- CE certified
- 1-year warranty
Technical Details
14 mm PLC basic terminal block for high switch-on currents with push-in connection, without relay or solid-state relay, for mounting on DIN rail NS 35/7,5, with load return line connection (BB), 1 N/O contact, input voltage 24 V DC
Product Documents
Datasheet
Technical specifications and performance data
User Manual
Installation and operation guide
