In Stock Hot Product
MKDS 3/ 8-5,08 GY
MKDS 3/ 8-5,08 GY 1128164 PHOENIX CONTACT Terminal for printed circuit board, pitch: 5,08 mm, number of pole..
$0.00USD
4805 in stock
Key Specifications
:0.2 mm² / flexible / > 10 N
Link:Screw connection with cage
Step:5.08 mm
note:Complies with WEEE/RoHS, no thread-like materials according to IEC 60068-2-82/JEDEC JESD 201
Supplier Information
Products: 0
Usually ships within 2-3 business days
Quality Guaranteed
Fast Shipping
Technical Support
Technical Specifications
| Parameter | Value |
|---|---|
| 0.2 mm² / flexible / > 10 N | |
| Link | Screw connection with cage |
| Step | 5.08 mm |
| note | Complies with WEEE/RoHS, no thread-like materials according to IEC 60068-2-82/JEDEC JESD 201 |
| type | Modular PCB terminal block |
| Result | Test passed |
| Amplitude | 0.35 mm (10 Hz ... 60.1 Hz) |
| Frequency | 10 - 150 - 10 Hz |
| Packaging | Packed in carton |
| Width [w] | 40.64 mm |
| Height [h] | 23 mm |
| Length [l] | 11.2 mm |
| Pin Layout | Linear Pinning |
| Shank sizes | 0.9 x 0.9 mm |
| Sweep Speed | 1 octave/min |
| Temperature | 850 °C |
| Acceleration | 5g (60.1 Hz ... 150 Hz) |
| Color (Case) | Grey (7042) |
| Note for use | A predefined tightening torque must always be observed for secure connection. Especially in the case of two- and three-pole PCB terminals, the single contact soldering tip may not block them. For this reason, the terminals must be reinforced when connecting (fixed by hand, reinforcement on the housing). |
| Product Line | COMBICON Terminals M |
| Product Type | PCB terminal block |
| Bore diameter | 1.3 mm |
| Mounting type | Wave Soldering |
| Article review | 00 |
| Number of rows | 1 |
| Product Family | MKDS 3 |
| Shank Distance | 15.24 mm |
| Surface Finish | Galvanic tin plating |
| Number of poles | 8 |
| Test Directions | X, Y, and Z axis |
| Contact Material | Cu Alloy |
| Rated Current IN | 24 A |
| Rated voltage UN | 400 V |
| Tightening torque | 0.5 Nm ... 0.6 Nm |
| Test Specification | DIN EN 60998-2-1 (VDE 0613-2-1):2005-03 |
| Dimensioned Drawing | |
| Installation Height | 18 mm |
| Insulation material | PA |
| Nominal cross-section | 2.5 mm² |
| Sizing voltage (II/2) | 630 V |
| Weld Shank Length [P] | 5 mm |
| Sizing voltage (III/2) | 400 V |
| Sizing voltage (III/3) | 250 V |
| Test duration per axle | 2.5 h |
| Duration of application | 5 s |
| Appliance type screw head | Longitudinal slit (L) |
| Insulation Material Group | The |
| CTI according to IEC 60112 | 600 |
| Conductor cross-section AWG | 24 ... 12 |
| Rated Impulse Voltage (II/2) | 4 kV |
| Minimum creepage value (II/2) | 3.2 mm |
| Rated impulse voltage (III/2) | 4 kV |
| Rated impulse voltage (III/3) | 4 kV |
| Rigid conductor cross-section | 0.2 mm² ... 4 mm² |
| Sizing Impulse Voltage (II/2) | 4 kV |
| Ambient temperature (mounting) | -5 °C ... 100 °C |
| Minimum creepage value (III/2) | 3 mm |
| Minimum creepage value (III/3) | 3.2 mm |
| Note on the Connection Section | In case of conductor connected by 4 mm² (rigid). |
| Rated Isolation Voltage (II/2) | 630 V |
| Sizing Impulse Voltage (III/2) | 4 kV |
| Sizing impulse voltage (III/3) | 4 kV |
| Ambient temperature (operating) | -40 °C ... 100 °C (Depending on current flow curve/derating curve) |
| Rated Isolation Voltage (III/2) | 400 V |
| Flexible conductor cross-section | 0.2 mm² ... 2.5 mm² |
| Heating verification requirement | Temperature rise ≤ 45 K |
| Rated insulation voltage (III/3) | 250 V |
| Length of the section to be stripped | 8 mm |
| Number of Welding Pins per Potential | 1 |
| Ambient temperature (storage/transport) | -40 °C ... 70 °C |
| Combustibility class according to UL 94 | V0 |
| Relative humidity (transport and storage) | 30 % ... 70 % |
| Metal Surface Welding Area (Surface Layer) | Tin (4 - 8 μm Sn) |
| 2 conductors of identical cross-section, rigid | 0.2 mm² ... 1.5 mm² |
| Insulation Resistance Between Contiguous Poles | 109Ω |
| Metal Surface, Connection Point (Surface Layer) | Tin (4 - 8 μm Sn) |
| 2 conductors of identical flexible cross-section | 0.2 mm² ... 1.5 mm² |
| Minimum creepage value - inhomogeneous range (II/2) | 3 mm |
| Minimum creepage value - inhomogeneous range (III/2) | 3 mm |
| Minimum clearance value - inhomogeneous range (III/3) | 3 mm |
| Resistance to surface currents (DIN EN 60112 (VDE 0303-11)) | CTI 600 |
| Brinell hardness test temperature according to EN 60695-10-2 | 125 °C |
| GWIT filament ignition temperature according to EN 60695-2-13 | 775 |
| Flammability index of GWFI filament according to EN 60695-2-12 | 850 |
| Flexible conductor cross-section with mounted lug and plastic collar | 0.25 mm² ... 2.5 mm² |
| Flexible conductor cross-section with cable lug without plastic collar | 0.25 mm² ... 2.5 mm² |
| Conductor cross-section/conductor type/tensile force nominal value/actual value | 0.2 mm² / rigid / > 10 N |
| 2 conductors of the same flexible cross-section with ferrule without plastic collar | 0.25 mm² ... 0.75 mm² |
| 2 conductors of identical cross-section flexible with TWIN ferrule with plastic collar | 0.5 mm² ... 1.5 mm² |
Product Description
Terminal block for printed circuit board, nominal current: 24 A, nominal voltage (III/2): 400 V, nominal section: 2.5 mm², number of rows: 1, number of poles per row: 8, article family: MKDS 3, pitch:
Key Features
- Industrial grade quality
- RoHS compliant
- CE certified
- 1-year warranty
Product Documents
Datasheet
Technical specifications and performance data
User Manual
Installation and operation guide
